======================================== EV-158A v2.0 - Everex RAM 10000 DELUXE ======================================== - Up to 10MB RAM - base, expanded (LIM EMS 4.0) and/or extended. - 1 MB DRAM 120ns or faster. All chips must have the same *speed*. - A bank must be fully populated. - If not populating all banks, start from bank 0 (eg. bank 0) (eg. banks 0/1) (eg. banks 0/1/2) - To use EMS, the supplied driver EMM.SYS must be used. - Multiple cards can be used to provide up to 32 MB EMS, which is the limit of LIM 4.0. - Bundled software/drivers INST158A.EXE: test of memory installed. EMM.SYS: EMS driver. EMML.SYS: used when EMM.SYS xxxxxxxxxxxxxxxxxx. EDISK.SYS, ESPOOL.EXE: RAM disk and Print spooler. (Not described here) .-----------------------------------------------------------------. |.---.---. .---.---. .---.---. .---.---. .---.---. !!!!!! !!!!! | .- || B | | | | | | | | | | | | | | SW 3 SW 4 |=| || A | 4 | | | 3 | | | 2 | | | 1 | | | 0 | .------. | | || N | | | | | | | | | | | | | | | | | | || K | | | | | | | | | | | | | | | | : | | || | | | | | | | | | | | | | | `------' W1 | | |`---'---' `---'---' `-------' `---.---' `---.---' | | | !!!!! SW 2 |=| `-------------------------------------nnnnnnnnn-nnnnnnnnnnnnnnnnn-' | """"""""" """"""""""""""""" | ............................................................................................................................................ W1: RAM parity Check. Shorted = enable parity checking. (Default) ............................................................................................................................................ SW2:1-4 EMS I/O Port Address, Y is automatically set to 0, 4, 8 or C. I/O address: Y208 Y218 Y258 Y268 Y2A8 Y2B8 Y2E8 (default = Y258) ---------------------------------- SW2:1 ON ON ON ON OFF OFF OFF 2:2 ON ON OFF OFF ON ON OFF 2:3 ON ON ON OFF OFF OFF OFF 2:4 ON OFF OFF ON ON OFF ON ............................................................................................................................................ SW2:5 Enable/disable EMS port. OFF is enabled - set the port address with SW2:1-4 ............................................................................................................................................ SW2:6 Reserved (it was OFF by default). ............................................................................................................................................ SW3:1-3 Number of populated memory banks. No. of banks: 1 2 3 4 5 ------------------- SW3:1 OFF OFF OFF OFF ON 3:2 OFF OFF ON ON OFF 3:3 OFF ON OFF ON OFF ............................................................................................................................................ SW3:4-10 Quantity of active memory, ie, base and/or extended. Any memory that is not made active will be available to the EMS driver. Active memory: 0MB 1MB 2MB 4MB 3MB 5MB 6MB 7MB 8MB 9MB 10MB -------------------------------------------- SW3:4 OFF OFF OFF OFF OFF OFF OFF OFF ON ON ON 3:5 OFF OFF OFF OFF ON ON ON ON OFF OFF OFF 3:6 OFF OFF ON ON OFF OFF ON ON OFF OFF ON 3:7 OFF ON OFF ON OFF ON OFF ON OFF ON OFF Above table for exact multiples of 1MB. If you desire a factional amount (e.g. 3.5MB), then also use the table that follows. Example: For 8.5MB, set 8MB per table above and then set 512KB per table that follows. Active memory: 0KB 128KB 256KB 512KB 384KB 640KB 768KB 896KB ----------------------------------------------- 3:8 OFF OFF OFF OFF ON ON ON ON 3:9 OFF OFF ON ON OFF OFF ON ON 3:10 OFF ON OFF ON OFF ON OFF ON ............................................................................................................................................ SW4:1 EMS transfer mode. Not applicable for XMS. OFF = 8 bits (default), ON = 16 bits. 16 bits may not be useable if the computer's bus speed is 8 MHz or faster. ............................................................................................................................................ SW4:2-8 Start Address for base/extended memory. Address: 0MB 1MB 2MB 4MB 3MB 5MB 6MB 9MB 7MB 8MB 10MB 11MB 12MB 13MB 14MB 15MB --------------------------------------------------------------------- SW4:2 OFF OFF OFF OFF OFF OFF OFF OFF ON ON ON ON ON ON ON ON 4:3 OFF OFF OFF OFF ON ON ON ON OFF OFF OFF OFF ON ON ON ON 4:4 OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON 4:5 OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON Above table for exact multiples of 1MB. If you desire a factional amount (e.g. 3.5MB), then also use the table that follows. Example: For 8.5MB, set 8MB per table above and then set 512KB per table that follows. 0KB 128KB 256KB 512KB 384KB 640KB 768KB 896KB --------------------------------------------- 4:6 OFF OFF OFF OFF ON ON ON ON 4:7 OFF OFF ON ON OFF OFF ON ON 4:8 OFF ON OFF ON OFF ON OFF ON ............................................................................................................................................ Parameters to EMM.SYS and EMML.SYS. In the normal case, do not set any. device=emm.sys [/c] [pppp] [/h:nnn] [/x:xxxx-cccc] [/i:iiii-dddd] [/t] /C Chain interrupt vector 67h if it is used by something else pppp Start address. C400 (default), C800, CC00, D000, DC00 or E000 /H: Max exp.memory handlers. From 64 (default) to 255. /X:, /i: Excludes/includes parts of the A000-FFFF. Eg. /x:CC00-CFFF /t Displays detailed information about EMM(L).SYS --- TEA 1992-10-02?