Note:  If you have not already done so, make sure that you run the 
AVGA2 INSTALL program to decompress Framework III from the root 
directory of the AVGA2 Drivers/Utilities Disk to a designated disk 
drive.  The following example will decompress and copy only the root 
contents of the AVGA2 Drivers/Utilities Disk to a designated drive.  
For example, type:

	install c:\avga2 root


Framework II will remain uncompressed in the AVGA2 Drivers/Utilities
Disk root directory, since Framework II looks to the root directory 
in Drive A: for the drivers.


AVGA2 Drivers for Framework II and III:
--------------------------------------
      
      Framework II requires that drivers to be installed are always 
      in the root directory of DRIVE A.  Installation instructions 
      for Framework II and Framework III are as follows:

      AVGA2 Drivers for Framework II

      Several drivers are included to support many different config-
      urations with the AVGA2's extended mode capability.  There are
      drivers that support both 132 columns and 800x600 graphics
      mode in the following table:

      Driver               Desktop Format          Zoom (F9) Format
      -------------------------------------------------------------
      AVGAFW21.SC          132x25 text             640x480 graphics
      AVGAFW22.SC          132x43 text             640x480 graphics
      AVGAFW23.SC          132x25 text             800x600 graphics
      AVGAFW24.SC          132x43 text             800x600 graphics
      AVGAFW25.SC          800x600 graphics        800x600 graphics
      -------------------------------------------------------------
				 Table 1.0

      If this is your first time doing installation, you can follow
      the instructions in the Framework II's Getting Started Manual
      manual and select the Standard IBM EGA, VGA and PS/2 display
      drivers.  Make sure your Framework II is functioning properly
      before proceeding with the installation of any of the AVGA2
      drivers.

      Setting up Framework II:

       1. Run the SETUP program from the Framework II "Setup" disk
	  from drive A: or from your Framework II subdirectory on
	  your hard disk.  Type:
	  ====> SETUP [ENTER]

       2. At the "Welcome to Framework II's Setup Program" menu:
	  ====> Select option "(2):  ALL OTHER USES OF THE SETUP
		PROGRAM."

       3. Now you need to tell the Setup Program the location of
	  the FWSETUP file that stores the current configuration.
	  ====> If you are using a floppy system, insert your
		SYSTEM DISK 2 into drive B: and select option (1).
	  ====> If you are using a hard disk system, select option
		(2), since FWSETUP should be in the Framework II
		subdirectory.

       4. At the "Main Menu"
	  ====> Select (2) CONFIGURATION

       5. You are now in the "Change Configuration" menu:
	  ====> Select (1) PRIMARY HARDWARE
	  ====> Select (1) SCREEN DRIVER
	  ====> Select (7) I want to enter my own driver file name.

       6. Enter the name of the driver you would like to use from
	  Table 1.0 above and hit [ENTER].  The complete driver name
	  including the .SC extension is required.

       7. Type "M" to return to the main menu.

       8. At the Main Menu:
	  ====> Select (7) SAVE ALL NEW SETTINGS

       9. You will then be prompted to insert your "Setup" disk into
	  drive A.  At this time, insert the AVGA2 Utilities/Drivers
	  disk in A: which contains the Framework II AVGA2 drivers.
	  Press the space bar when the driver disk is in drive A:.

      10. The Setup program will now save the current configuration
	  to the FWSETUP configuration file:
	  ====> Select (1) for floppy disk system
		(2) for hard disk system
		Then strike any key.

      11. You have now installed Framework II with the new AVGA2
	  driver.

      AVGA2 Drivers for Framework III

      Several drivers are included to support many different configur-
      ations with the AVGA2's extended mode capability.  There are
      drivers that support both 132 columns and 800x600 graphics mode
      in the following table:

      Driver               Desktop Format          Zoom (F9) Format
      -------------------------------------------------------------
      AVGAFW31.SC          132x25 text             640x480 graphics
      AVGAFW32.SC          132x43 text             640x480 graphics
      AVGAFW33.SC          132x25 text             800x600 graphics
      AVGAFW34.SC          132x43 text             800x600 graphics
      AVGAFW35.SC          800x600 graphics        800x600 graphics
      -------------------------------------------------------------
				Table 1.0

      If this is your first time doing installation, you can follow
      the instructions in the Framework III's "Up and Running
      Framework III" manual and select the "IBM PS/2 Model 50, 60 &
      80 drivers (VGA)" as the screen display.  Make sure your
      Framework III is functioning properly before proceeding with
      the installation of any of the AVGA2 drivers.

      Setting up Framework III:

       1. If you have installed Framework III on your hard disk, copy
	  all the Framework III AVGA2 drivers to your Framework III
	  subdirectory.  Using the example above, type the following:
	  ====> C:
	  ====> CD\ FW3
	  ====> COPY C:\AVGA2\ROOT\AVGAFW3*.SC

       2. Run the SETUPFW from your Framework III subdirectory on
	  your hard disk.  Type:
	  ====> SETUPFW [ENTER]

       3. At the "Welcome to Framework III's Setup Program" menu:
	  ====> Select option "(2):  ALL OTHER USES OF THE SETUP
	  PROGRAM."

       4. Now you need to tell the Setup Program the location of the
	  FWSETUP file that stores the current configuration.
	  ====> If you are using a hard disk system, select option (2),
		since FWSETUP should be in the Framework III
		subdirectory.

       5. At the "Main Menu"
	  ====> Select (1) Configuration

       6. You are now in the "Configuration Options" menu
	  ====> Select (1) Hardware
	  ====> Select (1) Screen driver
	  ====> Select (1) The screen driver I need isn't listed here
		[ENTER]
	  ====> Select (2) I want to enter my own driver file name
		[ENTER]

       7. Enter the name of the driver you would like to use from
	  Table 1.0 above and hit [ENTER].  The complete driver name
	  including the .SC extension is required.

       8. Type "M" to return to the main menu.

       9. At the Main Menu:
	  ====> Select (7) SAVE ALL NEW SETTINGS

      10. You will then be prompted "On which disk drive will Setup
	  find your Drivers Disk?".
	  ====> If you copied the Framework III AVGA2 driver files
		to drive C:, type C

      11. The Setup program will now need to write the new settings
	  to your FWSETUP file:
	  ====> Select (2).

      12. You have now installed Framework III with the new AVGA2
	  driver.

